Falcone Plumbing and Heating, Inc. is a licensed and highly qualified with a team of plumbing contractors who offer a wide array of plumbing services, shown below. We proudly serve clients in Saratoga, Cupertino, Sunnyvale, Campbell, Los Gatos, Monte, Sereno, Milpitas, Santa Clara, Mountain View, Willow Glen and surrounding areas of San Jose with over three generations of experience.
A plumbing or sanitation code is not a plumber’s code. It is rather a set of Rules and Regulations imposed by cities, counties and states on anyone who undertakes any work involving the installation of drinking water, sewer or toilet facilities in homes, offices, factories, schools and hospitals. Regardless of who might do the work, plumbing and sanitation codes require that it be done in a specific, safe manner because it was found that failure to do so caused widespread disease, which can be crippling and deadly-to the community.
Is licensing intended to prevent anyone but a plumber from doing sanitation work? NO… Licensing prohibits the irresponsible, incapable person from endangering the health of your family, neighbors sad community. Any person may do the work who has sufficient knowledge to do it in a safe manner, so long as the Rules and Regulations of the plumbing and sanitation code are observed. However, those wishing to do such work must demonstrate their ability by taking out a license and passing an examination.
The State requires that, like a doctor, nurse, dentist or pharmacist, anyone whose work affects the public health and safety shall have adequate knowledge and training. No one wants a “quack doctor” to treat his family or a “soda clerk” to fill his prescriptions. For precisely the same reasons, one does not want a “handyman” to do work in his home, office factory which can adversely affect the health of his family, his employees or his neighbors.
Done improperly this work would probably need to be rectified at the time the property changed hands which means paying twice for the same work.
This booklet was written with the objective of helping home owners as well as renters keep their plumbing systems in good operating condition. The sale value of a house with sound plumbing is far greater than that of a house where plumbing is in poor repair.
There are many things that an owner or renter can do; there are many things that should be left to an expert – the plumbing contractor and his staff of journeymen plumbers. Minor repairs should be made promptly. Such annoyances such as a clogged drain, dripping faucet or a leaking flush valve in the toilet, are more than a mere bother – they usually waste money. This booklet suggests remedies for these and many other household plumbing problems.
Major repairs, replacements, and new plumbing installations should be left to the supervision of a plumbing contractor. His working methods are based on years of experience – and his guarantee is assurance that all materials and methods are of the highest quality.
This booklet will help prolong the useful life of your plumbing system. Your plumber will be glad to give you additional hints that apply specifically to your own home.
Preventing this situation can be done by carefully watching what is emptied into the sink drain and by the regular use of a safe biodegradable waste digester. Your plumber can give you more information on these products.
Sink stoppages are usually caused by liquid fats, emulsified by warm dishwater and carried through the pipes. The water cools as it proceeds to the main sewer and leaves the fatty deposits along the way. A film of grease forms on the pipe wall, then another and another. Coffee grounds and bits of food add to this accumulation layer until the pipe becomes impassible.
Pour excess grease into a tin can and throw it out with the garbage, not down the sink drain. When using a food disposer, always let sufficient cold water run to carry the particles down and into the main line to prevent buildup in the smaller waste lines.
In the event of a stoppage, you should have a “plumber’s friend,” or plunger – a large rubber suction cup with a wooden handle. Cup it tightly over the drain and plunge it vigorously several times. If it is a double drain sink, make sure you seal the other drain, so water will not splash out into the other bowl or on you. Drain piping can also be cleaned by removing the J-bend on the trap below the fixture. First place adhesive tape around the packing nut or wrap the wrench jaws with cloth to prevent scratching the metal surface. If plastic piping is in place, do not grip the nuts too tightly with the wrench, as they can crack easily.
Place a bucket directly under the pipe to catch any dripping from the open pipe. Pull out the clogging material with a piece of wire or small hand-turned cable. If you take the trap off, have some new gaskets ready to slip into the joints.
A plunger will normally handle simple toilet clogs. Another method of cleaning a water closet trap or toilet is the use of an auger with an adjustable, crank-type handle. Known to plumbers as a “snake,” the spring-steel coil is easily worked past the trap and down the pipe. A three foot auger is inexpensive and will quickly drill through most clogs. Use the auger carefully. Careless handling may crack the toilet.
If the rubber-cupped plunger or the auger does not clear the toilet, call your plumber.
Heavy steel spring coils should not be used to clean traps under lavatories, sinks, or bathtubs. A more flexible type of wire or spring should be used — one which is easy to work through the bend of the trap.
When the clogging material has been removed from the trap, pour a pail or two of hot water into the drain to wash out any loose material. Check the strainer itself and clean it in hot water and soap in order to open all holes. The floor drain should be checked regularly, especially one that is not often used, since water in the trap may evaporate. This would allow sewer gases to enter the room. Pour a pail of water into the drain periodically in order to make certain of a proper water seal.
The best modern fittings are all chrome plated brass and will last a lifetime under everyday use. They clean easily with soap and warm water.
Caution: The metal chromium is easily dissolved in hydrochloric acid and sulfuric acid. Muriatic acid has for years been considered a good tile cleaner, but only where there are nickel plated plumbing fittings. Where chrome plating is present, clean bathroom tile with warm oxalic acid never with muriatic or sulfuric acids. Even covering the chromium surfaces with cloths will not prevent the acid fumes from inflicting permanent damage.
Gaining in popularity are polished brass fittings and trim. These will hold up well, as long as certain precautions are observed. NEVER use any abrasive cleaner on polished brass. This can scratch the protective coating on the brass finish resulting in a deterioration or pitting of the brass plating. Also avoid use of solvent based cleaners because they can be deleterious to the polished brass finish.
New technologies have brought about the development of improved finishes that can withstand more wear, but check the manufacturer’s warranty regarding it to determine whether or not you have the “new and improved” lifetime warranty finish.
A washerless faucet does not mean it will never leak, but rather because of the way it is designed, the parts will last much longer, as their design minimizes friction and wear.
When repairing this type of faucet or requesting service on one, it is vital that you know the brand name, or have a sample of the part you require, as there are hundreds of faucet cartridges and parts kits on the market today.
Your licensed plumber will carry an extensive assortment of faucet parts in his service truck, but it is impossible to carry absolutely every part. So it can be very helpful if he knows in advance, the brand of faucet.
In a compression type faucet, you will find the conventional setup – a faucet washer on the end of the stern. Replacing the washer usually will correct a dripping faucet.
However, when removing the stem, always check the seat inside the faucet body – the brass ring that the washer grinds against. The faucet seat can be worn or grooved, making the washer replacement ineffective within days. The washer and seat are the two parts of a compression type faucet that receives the greatest amount of wear. It is not difficult to replace a washer. First, shut off the water supply. Usually, the shut-off valve is under the sink in the kitchen, or in the bathroom, under the lavatory basin. If there is none, shut off the branch-line valve in the basement or the main valve where the water supply enters the house.
Pad a smooth jawed wrench with a cloth, then, using the padded wrench, unscrew the large packing nut and turn out the faucet stem. Then, with a screw driver that fits the screw slot closely, remove the screw from the bottom of the stem and pry out the worn washer. If the screw is tight or stubborn, tap its head lightly or apply penetrating oil (WD-40).
Next, clean out the washer seat or compartment. When this is done, insert the new washer of the correct size and composition for hot or cold water.
Some of the newer, soft neoprene washers are for both hot and cold water and have a long life. The washer should fit snugly without having to be forced into position. After inserting, replace the screw and tighten.
It is usually just as expensive to renew a seat as it is to buy a new faucet, unless it has been made with a renewable seat. Check with your plumber about a badly worn faucet.
With cloth over finger, clean the valve seat inside the faucet. The edge should be smooth and free from deep nicks. If you find it badly worn, you will probably need to replace the seat or have the entire faucet replaced by the plumber. Otherwise, it will leak again.
Next, replace the faucet stem and turn it in. Tighten the packing nut. Be careful not to tighten the nut more than necessary to stop seepage around the faucet stem.
Remembering that a faucet leaking 60 drops a minute (not unusual) will waste 2,299 gallons of water every year. Homeowners should repair leaky faucet at once. You pay twice – once for the water going through the meter, and then again on your sewer bill, which is based on water usage.
Bowls are available in Corian, Moenstone, Swanstone, Surrell, and others. The important thing to remember is to follow the manufacturer’s instructions pertaining to the material of which your bowl is constructed. With some of the solid surface materials, scratches can be removed when lightly sanded because the color goes throughout the thickness of the material.
To prolong the life and appearance of enameled cast iron sinks, clean the bowl immediately after use. Use a non-abrasive cleaner. Constant use of abrasive cleaners can eventually wear the finish down, making it much more porous and susceptible to stains. This can also happen with enameled, cast iron tubs over a long period.
Don’t allow fruit or vegetable juices or cleaning acids to stand on surface. An acid-resisting sink will safely resist lemon, orange, and other citrus fruit juices, tomato juice, mayonnaise, and other vinegar preparations if these are not permitted to remain more than a few hours. A regular enamel finish is not impervious to acids.
Teas and coffee grounds will also stain enameled surfaces, if allowed to remain very long. Photographic solutions are even more harmful to enamel, and the amateur photographer should not be allowed to use the sink, because a fixture once damaged in this way can never be corrected. When cleaning the sink, use hot water and soap. Water and soap are not as hard on the enameled finish as h2 cleaning solutions like washing soda or a gritty abrasive. If a cleaner is used, it should be one that specifically states that it is non- abrasive.
Never use abrasives on any of these materials. They can cause scratches to the surface. Usually they will clean with hot water and soap.
If that is not sufficient, a cleaning product recommended by the manufacturer of the fixture, or your plumber, can be used to handle heavier cleaning tasks.
With fiberglass and acrylic units, special polishes with no abrasives are available to protect their finishes, by sealing the pores in the material, which makes subsequent cleaning easier. When decorating the bathroom or repairing something near the bathtub, place a heavy cloth over every inch of the bathtub surface so paint, falling tools, etc., will not mar or chip the enameled surface. Do not stand in the bathtub with shoes, as the nails and grit in the soles will scratch the enameled surface. Fiberglass and acrylic hubs should be cleaned with non- abrasive cleansers recommended by manufacturers.
Seat bumpers should be replaced if worn. Defective bumpers may cause breakage of the seat or hinges.
Stains or moisture at the base of the closet bowl indicate that the joint or seal between the closet and its outlet have failed and should be reset immediately to prevent rotting of the floor, damage to the plaster of the ceiling below, and possible leakage of sewer gas into the home.
When the tank has refilled, if water continues to seep into the bowl or if there is a low humming noise, this indicates leakage from the tank. This leakage can occur from either the supply valve or the improper seating of the rubber tank ball or (flapper) on the discharge opening.
A small amount of food coloring added to the tank water will help you determine whether the tank ball in the bottom of the tank is leaking. Add it to the water aver the tank is filled. Watch for the coloring to seep into the toilet bowl, and if it does, the ball or flapper over the discharge opening is not water tight If the rubber tank ball does not fit tightly over the discharge opening, a defective ball, irregular seat or bent lift wires may be responsible. If the ball is worn out, misshapen or has lost its elasticity and fails to drop tightly into the hollowed seat, it should be replaced with a new one. Sometimes the ball is covered with a slimy coating which can easily be wiped off. To replace the ball, shut off the water supply (a stop is installed underneath the tank where the water may be conveniently shut off at this point) and empty the tank or place a stick under the ball float lever-arm to hold it up, thereby shutting off the intake cock and preventing the tank from refilling. Then unscrew the ball from the lower lift wire and attach a new ball of the same diameter as the old one. (Note: some old tank balls swell from age and absorption of water.)
If the collar or seat of the discharge opening is corroded or grit-covered, it should be scraped and sand-papered until it is smooth and forms a uniform bearing for the stopper.
Straighten or replace bent lift wires so that the ball drops squarely into the hollowed seat.
A leaky, waterlogged float ball holds the supply valve open and does not completely shut off the water. If the rod which connects the tank float to the supply valve has become bent, it may prevent the float from reaching its full height, thus leaving the valve open and allowing leakage. This rod should be straightened and a little oil applied to the lever joints to insure smooth action.
Sometimes the tank will not fill sufficiently or will fill to overflowing. These difficulties may be corrected without disturbing the supply valve by bending the rod attached to the tank float upward or downward. If the rod is bent upward, the water will rise higher in the tank, and if downward, the water level will be lowered.
An overflow tube or pipe is provided in the closet tank to take care of the water in case it should rise above its accustomed level which should be at least 3/4 of an inch below the top of the overflow. While there is not much danger of its becoming stopped up, it might be well to examine it occasionally to see that it is in working order.
If water rises to the top of the overflow pipe an adjustment or new fill-valve assembly is necessary. Consult your plumber if in doubt.
There is more potential for the scalding of a person showering if the pressure fluctuates. Most people aren’t aware that young children and older persons can be scalded much sooner than adults. Lowering the water temperature at the water heater will minimize the potential danger at the tub spout or shower head and is the best preventive action which can be taken to prevent scalding.
A small child doesn’t have to soak in overly hot tap water to get scalded. Tragically, injury can happen literally in the blinking of an eye. 150 degree water can scald in just 1/2 second, 140 degrees scalds in just I second, but it takes four minutes for water at 120 degrees to scald.
POINT OF CAUTION – – Never let a child bathe unattended, because of the danger of scalding and injury. In addition, always turn cold crater on first, followed by the hot water until the desired temperature is achieved. That way, no one is exposed to straight hot water.
You need not rush to buy another shower head if the one you have suddenly gives off an uneven spray. It’s probably clogged with mineral deposits which build up in the shower head and distort the shower stream.
If the shower head holes are clogged, remove the face of the shower head, clean the back surface and free holes with a coarse needle. The latest shower heads on the market are all self-cleaning and need no such attention. The only positive preventive measure is investing in a water softener. When changing shower heads, wrap adhesive tape around the packing nut or pad the wrench jaws with a cloth so you won’t mar the finish.
Shower curtains made of fabric such as heavy drill or canvas can be put into the washing machine or laundry tub. All other shower curtains should be washed by spreading flat on a table and sponging with sudsy water. Rinse the curtain with clear water, then wipe with a clean cloth. Turn the curtain over and repeat on the other side. Then replace on the shower rod and spread it out straight to dry. While you’re at it, give the shower rod a good cleaning.
Clean prefabricated shower cabinets with soap and hot water, but never with a gritty abrasive. New shower cabinets usually have fiberglass or acrylic walls which will not withstand heavy scouring powders. If you stand in it to wash the inside walls of the cabinet the receptor should be protected by a heavy cloth or papers.
Salt air or other corrosive atmospheres have a destructive effect on chrome. Where chromium- plated fittings are exposed to these agents, it is important to wash them frequently. After they are washed and dried, it is advisable to apply a protective coating such as ordinary furniture wax.
Green spots may appear on chromium plating. If this happens, prevent the rust from spreading by scouring the spots with the same kind of powder which manufacturers recommend for enameled, cast iron fixtures. When the spots have been removed, apply a Fin of wax. Your plumber will be glad to help you select a good cleanser.
If you have a gas or electric water heater, keep the temperature dial setting at or below the suggested Factory Energy Savings Settings listed on the water heater. Above that mark means excessive wear on the water heater and the potential for scalding.
The burner of a gas-fired water heater is easily accessible and should be checked by your plumber periodically to keep it clear of dust or sediment. The flame at full fire should be a light to dark blue. If the flame is more orange or yellow, the gas pressure or air flow needs to be adjusted.
You can keep your water bills low by tempering all hot water as it is used. Letting the hot water faucet run on and on wastes not only water but fuel as well. With all water heaters, plan your hot water needs and you’ll be delighted with the savings you get.
All domestic water heaters are required to be equipped with a relief valve as a safety feature to prevent damage from excessive pressure and temperature. There is always danger that this valve may become frozen or corroded from long disuse. For this reason, it is advisable to trip the lever of this valve manually every two or three months to be sure it will operate freely if an emergency arises. Note: The discharge will be hot water that will need to be contained in a pan or bucket or allowed to drain to a floor drain.
Another danger from the use of a torch arises when both ends of a pipe are clogged with ice and when the heat is applied in the center. The application of the heat of the torch at the center of the pipe is likely to cause the water to flash into steam potentially causing an explosion with disastrous results for the user of the torch.
It is far better to adopt the slower and more conservative procedure of melting ice by the use of a blow dryer, or heat gun.
Preventing Frozen Pipes
Before the cold freezing weather sets in, make sure that all the garden hoses outside your home are disconnected. Failing to do so can cause not only the hose but also the hose bib to which it is connected, to freeze and be damaged.
This is especially important with anti-freeze hydrants. The hose must be disconnected to make the faucet freeze-proof. Failure to do so will trap water in the faucet body, which then can freeze. If the hose is disconnected, the anti-freeze faucet can properly drain, and this will prevent freezing.
Water pipes which are exposed to freezing temperatures or drafts should be covered with insulation. Whenever possible it is best to drain systems not being used in severely cold weather. Small water pipes will freeze quicker than will waste or sewer pipes.
Never leave a garage door open in severely cold weather, if there is plumbing in the garage. The cold and draft can freeze water lines in minutes. Pipes located in unheated basements or garages should be insulated with a commercial covering.
When pipes are laid underground they should be below the frost line to prevent freezing.
Because so much of the noise is due to water traveling at a high velocity, it follows that whatever can be done to reduce the velocity of the water will correspondingly reduce the noise in the system. It is for this reason that it is so important not to skimp on the size of the water supply piping. Larger pipe will not only provide a more adequate supply of water but will reduce noise.
There are three general types of noises found in some of the older plumbing systems. These are water hammer, whistling and chattering.
Water hammer is the thump in the piping heard when faucets or valves are turned off abruptly. There is no excuse for water hammer. It can usually be eliminated by the installation of an air chamber or short length of pipe in the wall where each supply pipe enters a plumbing fixture.
In some cases, however, the ordinary type of air chamber will not prevent water hammer. In such cases, special devices known as shock arrestors should be installed on the main line near the meter or as close as possible to the cause of the noise.
Sometimes water hammer is due not to the plumbing in the house in which it is heard but to a condition outside of the house, either along the water main or in a neighboring house. In such cases, skillful detective work by an experienced master plumber is necessary to ferret out the source of the trouble and to plan corrective methods.
Water hammer should not be permitted to go on indefinitely. The noise is only an audible symptom of what is going on in the piping. The piping is being subjected to the wear and tear of a multitude of shock waves. The result will be leaks in piping, tanks or fixtures unless the condition is corrected.
Chattering in the piping may be caused by loose pipes, by pipes rubbing against a metal projection, by worn faucet washers or looseness of other inside parts.
Whistling is caused by the speed of water flowing through piping which is usually too small. A pressure reducing valve will help as will a general straightening out of the plumbing system. Whistling is most common at bends and tees in the pipe.
Normally, when not in use, the water and fixtures will worm rapidly to room temperature and the condensation will stop. When a closet tank or other fixture continues to sweat for hours after it has been used, it is a sign that cold water is continuing to flow through it, possibly due to an improper adjustment of the tank valve or a leak.
Sweating pipes can be wrapped with an insulation material which prevents the condensation and formation of moisture.
Unusual odors should never be ignored. Such odors are often an indication that sewer gas is present. Sewer gas, while not always deadly, is noxious and capable of causing headaches and other minor illnesses. Sewer gas is foul smelling air and should be prevented from entering the house.
If it is suspected that sewer gas is entering through a leak in the piping, a plumber will subject the system to a test either by means of smoke, water or oil of peppermint. The test will indicate the location of the leak.
In order to explain how the sewer gas may enter a house through a plumbing fixture, it is necessary to clarify the function of traps and vents. Every plumbing fixture is the terminus of the city water supply system and the beginning of the city sewerage system. The faucets control the water supply. The traps and vents control the sewer air. They do so by a very simple method. Sewer air will not penetrate a water barrier. Therefore, a device is employed which keeps several inches of water between the house air and the sewer air. This is the trap, which is plainly visible under such plumbing fixtures as sinks and lavatories. It is built into water closets. In the case of bathtubs and shower cabinets, it is usually concealed in the floor or basement.
A trap, however, would lose its water seal by siphonic action every time a fixture is used unless the air on the sewer side is balanced with the air on the house side. This is the function of the vents. Occasionally, due to changes in atmospheric conditions, a compactly vented trap will lose its seal.
Usually, however, when a trap loses its seal it is due either to incorrect design of the vents, absence of vents or to evaporation of the water in the trap. Traps under fixtures that are used infrequently should be filled with water from time to time to insure an adequate trap seal.
Shut off the water supply at the main shut-off valve at the street. Then beginning with those on the top floor, open all faucets and leave them open. When water stops running from these faucets, open the cap on the main shut off valve in the basement and drain the remaining water into a pail or tub. Remember that this cap must be closed after the faucets have run dry or the house water supply will flow from this valve and flood the basement.
Remove all water in the traps under sinks, water closets, bathtubs, and lavatories by opening the clean out plugs at the bottom of traps and draining them into a pail. If no plugs are provided, use a force pump or other method to siphon the water out. Sponge all the water out of the water closet bowl. Clean out all water in the flush tank.
Fill all traps with a non-freezing solution such as mineral oil, windshield washing fluid or RV type anti-freeze.
Drain all hot water tanks. Most water tanks are equipped with a vented tube at the top which lets air in and allows the water to drain out the faucet at the bottom. Make sure all horizontal pipes drain properly. Air pressure will get rid of trapped water in these pipes, but occasionally the piping may have to be disconnected and drained. To be safe have your plumber check your entire plumbing system.
If your house is heated by hot water or steam, drain the heating pipes and boiler before leaving. Burners and pilots should be completely out and the main water supply turned off at the basement wall or street. Draw off the water from the boiler by opening the draw-off valve at the lowest point in the system.
Open the water supply valve to the boiler so no water will be trapped above it. If you have a hot water system, begin with the highest radiators and open the air valve on each as fast as the water lowers. Every radiator valve must be opened on a one inch pipe system to release condensation.
Note: When you return home, refill all the systems BEFORE lighting the hot water heater or boilers.
One way to identify the valves is to have a tag on each valve indicating its function, that is, which fixtures or group of fixtures it controls. Valve- identifying tags may be obtained from plumbing dealers. Many plumbers are glad to offer a valve tagging service to their customers or prospective customers.
Another method of identification is by means of a valve chart. Because this is somewhat more elaborate, it is usually employed only for houses with several bathrooms. A drawing is made of the basement piping with all the valves indicated. The valves are numbered on the chart and tags with corresponding numbers are placed on the valves. Still another idea which aids in identification is to paint pipes a distinctive color.
Obviously, the most important valve in the house is the main shut-off valve for the entire plumbing system. This valve, generally located on the house side of the water meter, usually has a handle like a wheel If it has not been used in many years, it may require a wrench to turn it. Because the easy operation of this valve in case of emergency is so important, it is advisable to place a few drops of oil around the valve handle once or twice a year. This will prevent the sticking action of corrosion.
The shut-off valve may be the ground-key type with a small hole bored in its side for draining the pipes after the water is shut off or it may be a drain and stop with a cap nut covering the drain opening. In either case, close the opening before turning the water off. Unless this is done, water will spurt with force.
Where no means has been provided for shutting off a drain opening, drive a small wooden peg into it until the pressure is relieved by draining the piping that is exposed.
In addition to the main strut-off valve at the meter, the well plumbed house has individual shut-off valves on the branch lines leading to individual fixtures, groups of fixtures or equipment such as water heaters, water softeners, automatic washers, etc.
Many contractors, when installing plumbing fixtures, provide separate strut-off valves or stops for each individual fixture. These will be found on the supply lines below the fixture. These individual stops are a great convenience to regulate water flow in case of repairs as well as emergencies.
Conformance to these state requirements minimizes the possibility for the water using public to inadvertently contaminate or pollute the domestic water system or the public water supply.
This program requires the installation of a backflow prevention device in the plumbing system where the possibility of a cross connections may take place. A cross connection. is an arrangement of piping or faucets which allows the potable water supply to come into contact with a contaminant.
An example of a potential cross connection is a lawn irrigation systems, where fertilizers, chemicals or other contaminants can come into contact with the potable water supply through the irrigation heads.
There are several types of backflow prevention devices used today. The type of device is determined by the degree of hazard presented by the possible “cross connection”.
Most licensed plumbing contractors have one or more certified testers in their employ and will be happy to provide this service for you.
However, the spillage from the dump port does provide a “warning signals that the device is in need of maintenance.The needed service should be performed by a Certified Backflow Prevention Tester.
Backwater Valve. The function of this valve is to prevent the sewer from backing up into the house during heavy rains. Most backwater valves operate automatically. A valve with a butterfly action closes against the sewer on the house side.
Sometimes however, debris lodges against the seat of the valve so that it cannot close tightly. There are also manually operated valves, that have a wheel handle to shut them down. Sometimes, debris (mop strings, etc.) can accumulate or collect near the valve seat, which prevents it from closing tightly. With automatic backwater valves, removing the lid, cleaning the seat, and greasing the hinge pin on the valve gate annually will guarantee that the valve will operate as expected when it is called upon to prevent the water from coming into your basement. With the manual type of valve it is best to operate this valve manually every six months in order that (1) all members of the family may be familiar with the location of the valve with its function, and where the wheel for manual operation is stored; and (2) in order that the manual operation may keep the valve free from corrosion and lessen the chances for debris interfering with the valves closing.
Keep flammable products far away from the water heater or furnace, stored in an approved container, tightly closed and out of childrens’ reach. Flammable products, improperly stored or used near an open flame give off invisible vapors that can travel the length of a house and be ignited by any of a dozen or more household sources of flame or spark. A few precautionary measures can prevent a tragedy from taking place.
If the water closet is leaking, tell him it’s the water closet. If it’s the lavatory, don’t merely say that “there’s a leak in the bathroom” and expect him to tell you what to do until he gets there.
There are a thousand and one tools and parts in his plumbing store, and he can’t be expected to carry them all. So, when you ask for his help, give him as much information as you can. When he arrives, tell him everything that has been done to the defective part of the plumbing. It will speed his work and lower your plumbing bill.
Buying on the net is fun and easy as well. On the Internet buy from mail-order companies that have been in business for a while rather than the brand new ones or those that aren’t experienced. The new Internet companies seem to come and go and just like local suppliers it’s a good idea to buy from a company that will be there tomorrow. theplumber.com highly recommends companies that are part of The PlumbingSupply Group which are strictly Internet mail-order plumbing supply companies that have been on the Net since 1995. PlumbingSupply.com is one of those companies.
The professional team at Falcone Plumbing and Heating, Inc. look forward to speaking with you soon and working with you on your next project. We urge you to contact us with any questions regarding our plumbing services.